Author Topic: Big Mouth Bubbler plastic carboy  (Read 1772 times)

Offline KipDM

  • BeerSmith Master Brewer
  • ****
  • Posts: 77
  • Karma: 1
  • Brewing: makes friends and settles nerves!
Big Mouth Bubbler plastic carboy
« on: January 25, 2017, 01:23:47 PM »
there are several variants of these, but i bought the Siphonless Plastic version in both 6.5 and 5 gallon.
they are GREAT! the wide mouth makes it easy to reach your arm in and scrub everything clean as well as plenty of room for using your beer thief to check gravities.
also, being lighter makes them easier to lift in and out of my chest freezer. the bottom spigot is fairly typical of ported carboys.
the spigot is located above the yeast cake [unless you happen to also have a LOT of trub settlement like i did for a pumpkin beer] so you get clearer beer when transferring whether it's to a secondary or straight to a keg.

compared to other [glass] caroboys i've used over the years i would rate this a solid 9 out of 10, because nothing is perfect!
KipDM
On Tap: Autumn Amber, Columbus Warrior DIPA
Primary: none :(
Secondary: Pumpkin Spice Ale

Offline Retired18Z

  • BeerSmith Apprentice Brewer
  • **
  • Posts: 8
  • Karma: 0
  • BeerSmith 2 Rocks!
Re: Big Mouth Bubbler plastic carboy
« Reply #1 on: February 17, 2017, 04:38:20 PM »
So, I've been at this only a year... I never purchased glass carboys, only buckets (at first). I purchased one of these and thought it was the cat's pajamas, until I realized that yeast flocked out and hung on every "shelf" created by the large, structural ribs in the design. Nothing major but... Morebeer's Fermonster 6 or 7 gallon carboys give you the lightness of plastic, the wide mouth, but straight sides to help the yeast fall all the way down to the bottom. I agree, both of my wide mouth, clear plastic carboys are my favorites. The buckets serve a purpose, but the Big Mouth Bubbler and the Fermonster are, IMO, much better.

Offline BOB357

  • BeerSmith Grandmaster Brewer
  • *****
  • Posts: 108
  • Karma: 7
  • Beer is my bucket list!
Re: Big Mouth Bubbler plastic carboy
« Reply #2 on: March 06, 2017, 12:43:33 AM »
I love my Big Mouth Bubblers, but recently killed one of them. To clean Better Bottles I would mix a couple of gallons of PBW in the carboy and then invert it in a 2 qt. measuring bowl and let it sit until the krausen ring was gone. This method uses a lot less PBW for soaking and virtually no elbow grease.

I decided to use the same method with the bubblers. The flexing that occurs as the PBW solution glugs out into the measuring bowl until gets to the neck of the bubbler was a bit too much for the thin plastic. After about 15 cleanings a 4" crack showed up in the side along one of the transitions.

Now I use the kitchen sink sprayer to blast off what I can and then mix a gallon of PBW which I use to scrub the krausen ring with a micro-fiber cloth. I replaced the cracked bubbler with a 7 gal. Fermonster and  use the new method on it as well.
 
Bob

Offline KipDM

  • BeerSmith Master Brewer
  • ****
  • Posts: 77
  • Karma: 1
  • Brewing: makes friends and settles nerves!
Re: Big Mouth Bubbler plastic carboy
« Reply #3 on: October 19, 2017, 05:02:25 PM »
I love my Big Mouth Bubblers, but recently killed one of them. To clean Better Bottles I would mix a couple of gallons of PBW in the carboy and then invert it in a 2 qt. measuring bowl and let it sit until the krausen ring was gone. This method uses a lot less PBW for soaking and virtually no elbow grease.

I decided to use the same method with the bubblers. The flexing that occurs as the PBW solution glugs out into the measuring bowl until gets to the neck of the bubbler was a bit too much for the thin plastic. After about 15 cleanings a 4" crack showed up in the side along one of the transitions.

Now I use the kitchen sink sprayer to blast off what I can and then mix a gallon of PBW which I use to scrub the krausen ring with a micro-fiber cloth. I replaced the cracked bubbler with a 7 gal. Fermonster and  use the new method on it as well.

I pour more slowly so I don't have this flexing issue. But I too have started using a kitchen sprayer to get the initial crud off. I used to always use a 5-6 gallon PBW mix.
KipDM
On Tap: Autumn Amber, Columbus Warrior DIPA
Primary: none :(
Secondary: Pumpkin Spice Ale

Offline KB

  • BeerSmith Apprentice Brewer
  • **
  • Posts: 16
  • Karma: 1
  • My homebrew rocks!
Re: Big Mouth Bubbler plastic carboy
« Reply #4 on: Yesterday at 04:04:00 PM »
Nice being able to easily clean the wide mouth. However, the lids are VERY difficult to remove. Does anyone have any suggestions for making lid removal easier?

Offline Ck27

  • BeerSmith Grandmaster Brewer
  • *****
  • Posts: 256
  • Karma: -7
  • BeerSmith's Unofficial Spam Police.... Do Not Spam
Re: Big Mouth Bubbler plastic carboy
« Reply #5 on: Yesterday at 05:24:24 PM »
I'll have to check these out I've got 2 Cooper's Fermenters which are quite nice really and easy to use for dry hopping. I've got one 6.5 gallon bucket fermenter. 1 Speidel 7.9 gallon fermenter which is awesome hands down my nicest unit and durable as hell. I've also got a 1 gallon fermenter which I use for tests and whatnot.

Offline Baron Von MunchKrausen

  • BeerSmith Grandmaster Brewer
  • *****
  • Posts: 144
  • Karma: 5
  • Fermentation - a greater discovery than fire
Re: Big Mouth Bubbler plastic carboy
« Reply #6 on: Yesterday at 06:24:57 PM »
Nice being able to easily clean the wide mouth. However, the lids are VERY difficult to remove. Does anyone have any suggestions for making lid removal easier?

Interesting problem -  I wish I had.
With an aggressive fermentation needing blow-off tubes, my lids push up. I need to bungee cord the lids to the carrier handles to keep them sealed.

As to cleaning, I spray as much crud out as possible then add 1/2 cup PBW and fill to the top. All clean in a couple hours. I would not want to use any brushes inside plastic.
Outrageously Farfetched Brewery

Offline Ck27

  • BeerSmith Grandmaster Brewer
  • *****
  • Posts: 256
  • Karma: -7
  • BeerSmith's Unofficial Spam Police.... Do Not Spam
Re: Big Mouth Bubbler plastic carboy
« Reply #7 on: Yesterday at 07:04:06 PM »
Nice being able to easily clean the wide mouth. However, the lids are VERY difficult to remove. Does anyone have any suggestions for making lid removal easier?

Interesting problem -  I wish I had.
With an aggressive fermentation needing blow-off tubes, my lids push up. I need to bungee cord the lids to the carrier handles to keep them sealed.

As to cleaning, I spray as much crud out as possible then add 1/2 cup PBW and fill to the top. All clean in a couple hours. I would not want to use any brushes inside plastic.

Haha, sounds like what happened with the beer recipe I gave you.

Offline Baron Von MunchKrausen

  • BeerSmith Grandmaster Brewer
  • *****
  • Posts: 144
  • Karma: 5
  • Fermentation - a greater discovery than fire
Re: Big Mouth Bubbler plastic carboy
« Reply #8 on: Yesterday at 07:09:30 PM »
[Haha, sounds like what happened with the beer recipe I gave you.

Yup. It was an epic fermentation.
The hop haze has cleared. Now a nice IPA with mangos and pineapples.
Outrageously Farfetched Brewery

Offline Ck27

  • BeerSmith Grandmaster Brewer
  • *****
  • Posts: 256
  • Karma: -7
  • BeerSmith's Unofficial Spam Police.... Do Not Spam
Re: Big Mouth Bubbler plastic carboy
« Reply #9 on: Yesterday at 08:03:18 PM »
[Haha, sounds like what happened with the beer recipe I gave you.

Yup. It was an epic fermentation.
The hop haze has cleared. Now a nice IPA with mangos and pineapples.

:) Great I was worried about it when you told me it was having a bugger of a time clearing.

Offline BOB357

  • BeerSmith Grandmaster Brewer
  • *****
  • Posts: 108
  • Karma: 7
  • Beer is my bucket list!
Re: Big Mouth Bubbler plastic carboy
« Reply #10 on: Today at 12:54:08 AM »
Nice being able to easily clean the wide mouth. However, the lids are VERY difficult to remove. Does anyone have any suggestions for making lid removal easier?

That is a problem that can be solved by using a bit of keg lube or other food grade lubricant on the threads.
Bob

 

modification